Free Shipping Some Special Links
Special Promotions Season 10% off above
Promotion Time (01.01-12.30)
handle special lightweight , long-term use will not feel tired.
temperature heating element made of imported materials made with advanced technology , long life, low cost replacement of the heating element .
heating element using low voltage DC power supply, to ensure that the anti-static , no leakage , no interference.
split design, display easy.
200 ~ 480 temperature setting , temperature stable and accurate .
tip ( tip ) and international brands together , and according to different working conditions , matching each tip .
soldering station is made of a conductive material , to be truly anti-static .
Note: The general use should not exceed 380 . If you need to use a higher temperature , short time is allowed to use .
2 . Temperature lock
temperature setting to an appropriate temperature .
Use a screwdriver at the temperature knob clockwise to tighten the locking screw until the temperature setting knob does not move .
When the temperature re-set , screwdriver counterclockwise rotation locking screw loose .
3 non-stick tin tip reasons
tip temperature exceeds 400 .
to be used in the soldering tip surface did not give proper plus tin.
lack of flux in welding, soldering , repair, welding and other operations .
Wipe the tip on the sulfur content or dry sponge and a rag .
exposure to organic materials such as plastic , silicon ( Si ) quality grease and other chemicals .
Use impure and low tin content solder.
Replacement and handling tip
Unscrew sleeve tip can remove replaced. Be sure to turn off the power supply temperature control units and allow the tip to cool down before removing the tip, remove the oxide dust formed in the sleeve fixed premises . Care must be taken to avoid this dust into the eyes. Replace the tip and the normal hand strength to lock the sleeve .
When replacing the new iron core , iron core should be extended stainless steel pipe 23mm, then tighten the mounting screws in the handle iron core
Note: You must be careful not to over tighten , otherwise it will damage the heating element .
iron grip or temperature control units with a cloth moistened with a small amount of housing can be liquid detergent to clean .
Do not immerse the fluid temperature control units , or allow liquid to flow into the housing .
Do not use any solvents to clean the shell .
The new tip
Use Aetna replacement tip 900M series or selection of imported 936 tip .
When any time using the new tip, please follow these steps will make life considerably lengthened tip .
the low temperature setting control knob to the position . Turn the power “switch .”
heating arrive after 200 , the surface of the tip soldering flux containing tin wire added .
After heating at 200 continued for five minutes , and then transferred to the appropriate temperature setting controls the temperature position.
After reach the appropriate temperature , to get started.
Note: Any time using the new tip every day the best tip can remove foreign objects and clean interior !
Proper use of the soldering iron
soldering iron grip : A. Low iron : like holding a pen to write . B. High temperature soldering : finger down grip .
Tip the ideal angle for PCB : 45 .
Tip need to be kept clean .
When using a soldering iron touch the heating element is strictly prohibited .
When using non- violent use of iron ( example: hitting a hard object with tip ) .
In order to ensure good function allows normal operation temperature soldering iron , please note the following recommendations. ( If there are certain sets of iron or temperature factors function does not work correctly , please contact the nearest service support services at ) . Tip supplied are all alloy head , if used properly, will have a longer life.
Before the shutdown must be disabled at the tip soldering surface plus the appropriate amount of tin, just before welding smear .
Do not allow the tip long stay in the high temperature , easy to make the tip surface plating layer cracking.
When soldering iron tip should not be too much pressure to the friction pads , this process does not change the thermal performance, but will make the tip damage.
Do not use absolute tip cleanup materials or rough rasp .
If the surface is non-stick tin oxide , can be used as needed 600 to 800 James Bond aim carefully rubbing with emery cloth or ethyl alcohol solution to clean up equal , heated to 200 immediately ? Cheng Yuan Yue Po Cheng Tun ?
Do not use excessive chlorine or acid flux . Use of a synthetic resin or only flux activated resin .
Note : Every 24 hours or at least once a week , remove the tip to clean and remove foreign objects inside the sleeve .
When the power is turned on , the tip temperature is hot. Given the abuse may cause burns or fires , strictly observe the following:
Do not touch the metal parts near the tip .
Do not use near flammable objects tip .
notify other personnel workshop , the tip burns easily , may lead to dangerous accidents, should be completed after the break , or turn off the power .
When replacing parts or devices tip , you should turn off the power , and until the tip is cooled to room temperature.
To avoid damage to the welding station and safe working environment , shall comply with the following:
This product uses three-wire grounding plug must be inserted into the three-hole grounded outlet . Do not change the plug or use an ungrounded three adapters leaving poorly grounded .
For an extension cord , use a grounded three -wire power cord.
Do not use the soldering iron tip to work outside .
Do not knock the table in order to remove residual iron , a move that could seriously damage the earthquake iron .
Do not tamper with welding units .
Do not wet welding sets , or wet hands when using the welding station .
welding will smoke , workshops should be well ventilated.
without any physical injury or damage may be frivolous objects when using the solder
Thanks for your order!
Questions, issues or concerns? I'd love to help you!